Help / Measuring guide

How to measure your kitchen

Accurate measurements mean your units fit first time. It takes about 30 minutes.

Before you start

Work in millimetres

All our unit sizes are in mm, so measuring in mm avoids conversion mistakes.

Measure at three heights

Walls are rarely straight. Measure at floor, worktop and ceiling height and use the smallest.

Measure twice

Check every number a second time. It's quicker than returning a unit.

Take photos

Photograph every wall, including pipes, sockets and the boiler. They help if you send us your plan.

Measure step by step

Work clockwise around the room from the door. Write every measurement in millimetres on your sketch.

  1. Sketch the room

    Draw a bird's eye view of the room. It doesn't need to be to scale. Mark every wall, door, window, radiator and alcove, and number each wall.

    WindowDoorSink 1234
  2. Measure each wall

    Measure every wall from corner to corner, at floor, worktop (around 900mm) and ceiling height. Write down the smallest of the three.

    Floor: 3012mm Worktop height: 3004mm (use this) Ceiling: 3010mm Walls bow, so always use the smallest
  3. Measure the ceiling height

    Measure from the floor to the ceiling in a few places. You'll need this for tall units and to choose wall unit heights.

    Floor to ceiling Check again here Decides wall and tall unit heights
  4. Measure windows

    For each window, record:

    • Distance from the nearest corner to the frame
    • Width of the frame
    • Floor to windowsill
    • Floor to top of the frame
    A To frameB Width C To sill D To top
  5. Measure doors and openings

    Record the distance from the corner, the width including the frame, and which way the door swings. Doors must be able to open past your units.

    Corner to frameWidth Door swing Plan view from above
  6. Mark your services

    Mark where these are, measuring from the nearest corner and up from the floor:

    • Water supply and waste pipe
    • Gas supply
    • Sockets, switches and cooker point
    • Boiler and extractor duct
    • Radiators
    From cornerFrom floor WaterSockets BoilerRadiator
  7. Note any obstacles

    Record anything that sticks out from the wall: boxed in pipes, beams, chimney breasts or bulkheads. Measure their width, depth and height.

    WidthDepth below ceiling Chimneybreast Boxed pipe Also note how far each sticks out

Our unit sizes

Use these to work out how many units fit along each wall.

UnitHeightDepthWidths available
Base units720mm (870mm with legs)560mm (460mm and 300mm reduced depth)150mm to 1200mm
Wall units575mm, 720mm or 900mm300mm150mm to 1000mm
Tall units1970mm or 2150mm560mm (300mm reduced depth)300mm to 600mm
Worktop height (finished)Around 910mm600mm worktopCut to length
Plinth150mm3000mm lengths

Sizes are carcase sizes. Doors add around 20mm to the depth.

Gaps and clearances

Leave these spaces so doors open, appliances fit and your worktop sits right.

50mm

Filler next to walls

Leave a filler where a unit meets a wall or tall unit, so doors and drawers open without catching.

450–500mm

Worktop to wall units

The usual gap between the worktop and the underside of your wall units.

650–750mm

Hob to extractor

Check the exact distance in your hob and cooker hood instructions.

1000mm+

Walkway space

Leave at least 1000mm between facing runs of units so doors and drawers can open.

600mm

Appliance spaces

Most integrated dishwashers and washers need a 600mm space. Always check the appliance spec.

100mm

Corner clearance

Allow for handles in corners, where two doors can clash if there's no filler.

Common mistakes to avoid

  • Measuring one height only. Walls bow, so one reading can be 10mm or more out.
  • Forgetting skirting boards and tiles. Measure plaster to plaster and remove skirting behind units.
  • No fillers at walls. Units pushed tight to a wall often can't open.
  • Missing the door swing. Check room and appliance doors don't hit your units.
  • Guessing appliance sizes. Check the installation size in the manual, not the product size.
  • Ignoring the boiler and pipes. They often decide where wall units and tall units can go.

Not sure what you need?

Send us your sketch and measurements and we'll plan your kitchen for free, with a full parts list order easily.

Measuring FAQs

Should I measure in millimetres or centimetres?

Millimetres. All our units are sized in mm, so you can match your measurements straight to our range.

My walls aren't straight. What should I do?

That's normal. Measure at three heights and use the smallest figure, then use fillers to cover the gaps.

Do I measure from the skirting board or the wall?

From the wall. Skirting is usually removed behind kitchen units.

Do the unit heights include the legs?

No. Base units are 720mm high and the legs add 150mm, giving 870mm before the worktop.

I'm fitting a new floor. Does that change anything?

Yes. Take your height measurements from the finished floor level, including the new flooring and underlay.

Can you check my measurements?

Yes. Send us your sketch, measurements and photos using Submit your plan and we'll plan your kitchen for free.

What if a unit doesn't fit?

Unopened, unused units can be returned under our returns policy. Return delivery charges may apply.